- 您现在的位置：买卖IC网 > Sheet目录889 > V048T080M030 (Vicor Corporation)VTM CURRENT MULTIPLIER 8V 30A
Not Recommended for New Designs - Replaced by VTM48Ex080y030A00
Pin / Control Functions
+In / -In DC Voltage Ports
V048F080T030
The VTM current multiplier input should be connected to the
4
3
2
1
PRM ? regulator output terminals. Given that both the regulator and
current multiplier have high switching frequencies, it is often good
practice to use a series inductor to limit high frequency currents
between the PRM module output and VTM module input capacitors.
The input voltage should not exceed the maximum specified. If the
input voltage exceeds the overvoltage turn-off, the VTM module will
shutdown. The VTM module does not have internal input reverse
polarity protection. Adding a properly sized diode in series with the
positive input or a fused reverse-shunt diode will provide reverse polarity
protection.
+Out
-Out
+Out
-Out
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
A
B
C
D
E
H
J
K
L
M
N
P
R
T
+In
TM
VC
PC
-In
TM – For Factory Use Only
VC – VTM Control
The VC port is multiplexed. It receives the initial V CC voltage from an
Bottom View
upstream PRM regulator, synchronizing the output rise of the VTM
module with the output rise of the regulator. Additionally, the VC port
provides feedback to the PRM to compensate for the current multiplier
output resistance. In typical applications using VTM modules powered
from PRM regulators, the regulators VC port should be connected to
the VTM module VC port.
The VC port is not intended to be used to supply V CC voltage to the
VTM module for extended periods of time. If VC is being supplied from
a source other than the PRM regulators, the voltage should be removed
after 20 ms.
Signal Name
+In
–In
TM
VC
PC
+Out
–Out
Pin Designation
A1-E1, A2-E2
L1-T1, L2-T2
H1, H2
J1, J2
K1, K2
A3-D3, A4-D4,
J3-M3, J4-M4
E3-H3, E4-H4,
N3-T3, N4-T4
PC – Primary Control
The Primary Control (PC) port is a multifunction port for controlling the
current multiplier as follows:
Disable – If PC is left floating, the VTM module output is enabled.
To disable the output, the PC port must be pulled lower than 2.4 V,
referenced to -In. Optocouplers, open collector transistors or relays
can be used to control the PC port. Once disabled, 14 V must be
re-applied to the VC port to restart the VTM module.
Primary Auxiliary Supply – The PC port can source up to 2.4 mA
at 5 Vdc.
+Out / -Out DC Voltage Output Ports
The output and output return are through two sets of contact
locations. The respective +Out and –Out groups must be connected in
parallel with as low an interconnect resistance as possible. Within the
specified input voltage range, the Level 1 DC behavioral model shown
in Figure 16 defines the output voltage of the VTM module. The
current source capability of the VTM module is shown in the
specification table.
To take full advantage of the VTM current multiplier, the user should
note the low output impedance of the device. The low output
impedance provides fast transient response without the need for bulk
POL capacitance. Limited-life electrolytic capacitors required with
conventional converters can be reduced or even eliminated, saving cost
and valuable board real estate.
Figure 9 — VTM current multiplier pin configuration
VTM ? Current Multiplier
Page 5 of 11
Rev 2.8
01/2014
vicorpower.com
800 927.9474
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
V048T240T012
VTM CURRENT MULTIPLIER 24V 12.50
V110A48M400BL2
CONVERTER MOD DC/DC 48V 400W
V110B48M200BL3
CONVERTER MOD DC/DC 48V 200W
V110C8M75BL3
CONVERTER MOD DC/DC 8V 75W
V150A48M500BL
CONVERTER MOD DC/DC 48V 500W
V150B8M200BL2
CONVERTER MOD DC/DC 8V 200W
V150C48M150BG2
CONVERTER MOD DC/DC 48V 150W
V24A5H400B2
CONVERTER MOD DC/DC 5V 400W
相关代理商/技术参数
V048T080T030
功能描述:VTM CURRENT MULTIPLIER 8V 30A RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
V048T096M025
制造商:Vicor Corporation 功能描述:VTM CURRENT MULTIPLIER 9.6V 25A
V048T096T025
功能描述:VTM CURRENT MULTIPLIER 9.60V 25A RoHS:是 类别:电源 - 板载 >> DC DC 转换器（分解式） 系列:V-I Chip™, VTM™ 应用说明:Factorized Power Architecture and V-I Chips 产品培训模块:VI Chip Bus Converter Modules 标准包装:1 系列:V-I Chip™, BCM™ 类型:总线转换器模块 输出数:1 电压 - 输入（最小）:330V 电压 - 输入（最大）:365V 输出电压:12.5V 电流 - 输出（最大）:24A 电源（瓦） - 制造商系列:300W 电压 - 隔离:4.242kV（4242V） 应用:商用 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:1.28" L x 0.87" W x 0.26" H（32.5mm x 22.0mm x 6.7mm） 包装:托盘 工作温度:-55°C ~ 125°C 效率:95.3% 电源（瓦特）- 最大:300W 重量:0.031 磅（14.06g）
V048T120M025
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTM Current Multiplier
V048T120T025
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTM Current Multiplier
V048T160M012
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier
V048T160M015
制造商:Vicor Corporation 功能描述:VTM CURRENT MULTIPLIER 16V 15A
V048T160T012
制造商:VICOR 制造商全称:Vicor Corporation 功能描述:VTMa?￠Current Multiplier